You are here: Home » News » Technical Article » Single Disc Wafer Check Valve: One Flap in The Flange Gap

Single Disc Wafer Check Valve: One Flap in The Flange Gap

Views: 0     Author: J-VALVES     Publish Time: 2026-11-17      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Single Disc Wafer Check Valve: One Flap in The Flange Gap


A valve that lives in the gap

A single disc wafer check valve has no flanged ends of its own. The body is a short disc of cast or forged material, of which the DN65 CF8M single flap wafer check valve is one form, and it is clamped between two pipeline flanges that were already in the drawing. The pipe flange is the end connection, the line gasket is the joint, and the wafer only fills the space a spool would have taken. That is why the length is not read from ASME B16.10: for this body style the governing document is API 594, which fixes the wafer dimension so a valve drops into a gap that was built to the standard.

The seat is carried by the line flange

The disc lands on a seat machined into the wafer, but nothing in the wafer seals to the pipe by itself. The joint is made by two line gaskets compressed between pipe flange and body face. Two things follow. The gasket bore has to clear the disc: a spiral wound gasket whose inner ring stands proud of the compression face, or a sheet gasket cut small, sits in the disc path and holds it off the seat. And the wafer has no stiffness against a warped or non-parallel flange pair, so a joint pulled up on a mismatch cocks the body and the disc stops landing square. Gasket intrusion is a joint fault blamed on the valve.

One flap, one short arc

One disc, hinged at one side, travels a short arc, a fraction of the travel of a swing check at the same size. Reverse flow has only a short distance to cross before the disc is back on the seat, which is why this body closes early and gets chosen where a swing check would let a slug through. The same geometry sets the limits: one mass means one blow at large sizes instead of two smaller ones, and at low flow the disc hovers near the seat instead of standing open, wearing a narrow band and chattering. A spring holds it closer and shortens the hover, at the price of a small permanent loss.

Why the studs get longer

Swap a flanged check valve for a wafer body and the joint gets shorter while the studs get longer, because each stud now spans two flange thicknesses, the wafer, two gaskets and the nuts. Studs kept from the old valve leave a few threads in each nut, which is not a joint. The bolt holes in the wafer follow a flange drilling, ASME B16.5, EN 1092-1 or JIS, so a wafer drilled to one standard will not pass the studs of another, and the flange pair has to be spread to insert the body, which means the pipe has to be able to move. Stud length belongs in the enquiry.

Lug or wafer: what actually changes

Same width, same disc, same seat. A lug wafer check valve carries threaded inserts so it can be bolted to one flange and hold a dead end, and so either side can be opened without the other. That matters where a line is blinded, hydrotested or opened for inspection and the pipe cannot be dropped. In a continuous run between two flanges the lug buys nothing and costs money; the plain wafer is the honest choice.

Orientation, and the direction that kills it

A spring loaded wafer check valve is often called position independent, and mechanically it is, because the spring closes the disc wherever the body is rotated. Gravity is the part that is not independent. Hinge pin horizontal, flow horizontal or upward, and the disc falls back with help, which is the arrangement to draw on the installation sketch. Vertical upflow works, with the spring carrying more of the closing. Vertical downflow is the one to refuse: the disc hangs into the flow, gravity holds it open, and the spring alone must close it against a falling column, which is how stop pins bend and seats get hammered.

How it fails, and why nobody notices

There is no bonnet, no cover and no indicator. The body is the whole valve and the joint is the only access. Hinge pin and bushing wear lets the disc sit off axis and the seat contact narrows to a crescent. Debris held on the seat while the disc closes prints a line. A gasket that crept inward holds the disc off. None of it shows from outside: reverse flow looks like a pump losing prime or a line draining overnight, and the valve is the last suspect because it is the only item nobody can open. Closure testing to API 598 at 1.1 times the rating proves the valve that left the works, not the joint you built. The same argument about a gasket doing the sealing applies to a flanged basket strainer, where the cover joint is the wear part.

What to write on the enquiry

Size and class in the units of the line flange standard, body material, disc and seat material, the API 594 wafer dimension, spring or no spring, lug or plain wafer, whether gaskets and studs are in the supplier scope, and the closure test rating. J-VALVES builds this body with a single flap in CF8M, and the same wafer with threaded lugs in WCB, from 1 in upward; the rest of the range sits on the check valve page.

Body style How it closes At low flow Opened in line Where it fits
Single disc wafer short arc, one flap, spring assisted disc hovers near the seat no clean liquid, moderate size, fast closure
Dual plate wafer two half discs on one pin lighter plates sit further open no gas and large lines where slam is the worry
Lug wafer as single disc as single disc one side only end of line, blind and test points
Flanged swing check long arc, gravity disc rests on the flow yes, cover on body dirty service, large sizes, low velocity
Lift check straight lift, guided needs steady flow to stay open yes small bore, high pressure, steam

Frequently Asked Questions

Can a single disc wafer check valve be installed vertically?Yes, with flow upward and a spring fitted. Vertical downflow is the case to avoid, because the disc then hangs into the flow and only the spring closes it.

Does the valve come with gaskets and studs?Normally no. Gaskets and studs are line items and the stud length changes when a wafer body replaces a flanged valve, so both have to be ordered with the valve rather than found on site.

How can I tell whether it is leaking backwards?There is no external symptom. Isolate downstream and watch whether the pressure or level holds; a works closure test to API 598 at 1.1 times the rating tells you about the valve, not about the flange joint you assembled.

Manufacturer and supplier of industrial valves, including Floating Ball Valves, Trunnion Ball Valves, Flanged Gate Valves, Welded Gate Valves, High Pressure Gate Valves, Globe Valves, Swing Check Valves, Double Disc Wafer Check Valves, Y Strainers , etc. For more information, please send us your email .

QUICK LINKS

PRODUCTS

CONTACT US

Tel:+86 15158426559
Fax:0086 577 56692524
WhatsApp:+86 13600648865
Address:Wenzhou China
Ball Valves,Gate Valves,Globe Valves,Check Valves,Butterfly Valve,Strainer.
Copyright © 2020 J-VALVES. All Rights Reserved | Support by Leadong | Sitemap |  Privacy Policy