Views: 0 Author: J-VALVES Publish Time: 2026-11-17 Origin: Site
Procurement documents for international projects routinely ask for valves that are "ASME and PED certified" in the same line item, as if the two were interchangeable stamps of the same kind. They are not, and the gap between them is where most dual-certification problems are born. ASME standards answer an engineering question: was this valve designed, made and tested correctly? The Pressure Equipment Directive 2014/68/EU answers a legal question: may this specific valve lawfully be placed on the European Union market, and by whom, and with what evidence? A valve can be perfectly built to ASME B16.34 and be illegal to sell in Germany; a valve can carry a CE mark under PED and still disappoint you mechanically. This article walks through both regimes the way a buyer or EPC engineer needs to see them: what "ASME-certified" actually attaches to for a valve, what PED conformity legally requires, how the PED category and module are determined for ball valves, gate valves, globe and check valves, the five places where PED demands more than the ASME standards ever will, and the specification language that gets you a genuinely dual-compliant valve instead of paperwork assembled after the fact.
The fastest way to think clearly about dual certification is to separate the questions. The ASME family - B16.34 for pressure ratings and design, B16.10 for face-to-face dimensions, Section II for materials, Section IX for welding, plus API 598 and API 6D for testing - is a set of engineering standards. Compliance is largely a manufacturer's declaration: the valve was designed to those rules, made with those materials, tested to those procedures. There is no ASME stamp for a B16.34 isolation valve. The ASME U-Stamp you may have seen on pressure vessels attaches to equipment built under ASME Section VIII with an Authorized Inspector's involvement; an industrial valve is not such an item, and no equivalent third-party marking exists for a B16.34 valve. When a purchase order says "ASME certified valve," what is actually being bought is design compliance, material certificates and test records - not a stamp.
PED 2014/68/EU is a different animal entirely: it is law, not engineering convention. It applies to pressure equipment and accessories with a maximum allowable pressure PS above 0.5 bar, it determines legally which conformity assessment route the manufacturer must follow, and for anything at or above Category I it requires CE marking, a signed EU Declaration of Conformity, and for the higher categories the involvement of a Notified Body - a testing and certification organization authorized by an EU member state. CE marking under PED is not a quality label and says nothing about performance level; it is a legal statement that the essential safety requirements of the Directive have been met through the required assessment procedure. The two regimes therefore stack, they do not substitute: API and ASME compliance can satisfy the technical substance of many PED requirements, but it does not itself confer PED compliance, and PED conformity says nothing about whether the valve performs well in your service.
Because so many purchase orders lean on the phrase, it is worth listing precisely what an ASME-compliant valve purchase delivers. The pressure-temperature rating comes from B16.34 material group tables - the discipline covered in our B16.34 pressure-temperature rating guide. The shell design, wall thickness and allowed pressure classes come from the same standard; face-to-face and end connections from B16.10 and B16.25; materials from ASTM specifications whose properties are anchored in ASME Section II; welding on the pressure boundary from Section IX procedures. Testing follows B16.34's own hydrostatic rules or API 598, and the leak acceptance is whatever class the specification calls out. All of this is verifiable - the documents are concrete - but every link in that chain is either a manufacturer declaration or an inspection the buyer's inspector witnesses. An Authorized Inspector exists in the ASME vessel world; for a B16.34 valve, nobody outside the manufacturer's quality system signs anything by default.
That is not a weakness of the standards; it is simply their design. The engineering rules are strict, the market polices them through reputation and audit, and buyers who care add witnessed inspection to the purchase order. But it does mean the phrase "ASME certified" must be read as "designed, made and tested to ASME standards," and it explains why the PED side of a dual-certified valve feels so much heavier: PED adds a legal layer - classification, modules, notified bodies, declarations - that has no counterpart in the ASME system at all.
PED 2014/68/EU governs pressure equipment placed on the EU market with a maximum allowable pressure greater than 0.5 bar. Valves enter its scope as pressure accessories - components with an operational function whose housing is subject to pressure. One special class exists: safety accessories, chiefly pressure relief valves, which are automatically Category IV, the highest risk class, with narrow exceptions where the relief device is designed for one specific piece of protected equipment. This is why a safety valve supply is legally a different weight class from an isolation valve supply; the sizing and selection work for those devices is covered in our API 520/526 safety valve guide.
The classification logic rests on three inputs every RFQ must state: the fluid group, the state of the fluid, and the pair PS and DN. Fluid Group 1 covers dangerous fluids - flammable, explosive, oxidising, toxic - as classified under the CLP regulation; hydrocarbons, hydrogen and most process chemicals land here. Group 2 is everything else, including steam, air and water. The state matters because gases are treated more strictly: a fluid counts as a gas if it is a gas, liquefied gas, dissolved gas or vapour - or if its vapour pressure at the maximum allowable temperature exceeds 0.5 bar above normal atmospheric pressure. The consequences of classification - which category, which module, which documents - are the entire legal content of "PED certified," and they are worked out valve by valve, size by size. A DN25 valve and a DN300 valve of identical design can sit in different categories, and the supplier cannot determine any of it if the RFQ only says "Class 300" without stating the fluid, PS and TS.
Pressure accessories are classified against the piping tables of PED Annex II - Table 6 for Group 1 gases, Table 7 for Group 2 gases, Tables 8 and 9 for liquids. The controlling quantities are DN and the product of PS times DN, and the boundaries are sharp. The essential structure for gas service valves, consolidated from the Annex II tables, is:
Table | SEP (no CE) | Category I | Category II | Category III |
|---|---|---|---|---|
Table 6 - Group 1 gas (flammable/toxic) | DN <= 25 | DN > 25 up to 100, PS x DN <= 1000 | DN > 100 up to 350, PS x DN > 1000 up to 3500 | DN > 350 or PS x DN > 3500 |
Table 7 - Group 2 gas (steam, air, N2) | DN <= 32 and PS x DN <= 1000 | DN > 32 up to 100, PS x DN > 1000 up to 3500 | DN > 100 up to 250, PS x DN > 3500 up to 5000 | DN > 250 or PS x DN > 5000 |
Three worked examples show how fast the category moves. A DN50 ball valve on natural gas at PS 16 bar: PS x DN is 800, DN is above 25, so it is Category I - self-declaration territory. The same DN50 valve at PS 100 bar gives PS x DN of 5000, above 3500, and it lands in Category III - a Notified Body becomes legally involved. A DN100 gate valve on hydrogen at PS 100 bar gives 10000 and is also Category III. Compare that with a DN25 valve at PS 100 bar on the same gas: DN is not above 25, so it is outside the categories altogether - Sound Engineering Practice, discussed next. Liquid service is more forgiving; the highest category a liquid-service valve reaches under the piping tables is III for Group 1 fluids, and the entry thresholds are higher. Two further details matter in practice: unstable gases classified in Category I or II are raised to Category III, and where a valve serves in an assembly, the assembly's protection requirements can pull the highest applicable category into the evaluation.
A valve below Category I - small-bore valves on Group 1 gas, and most modest liquid-service valves - is not free of PED obligations; it is governed by Article 4(3), Sound Engineering Practice. The manufacturer must design and make it to the sound engineering practice of a member state, supply adequate instructions for use, and identify itself. What it must not do is affix a CE mark for PED, and no Declaration of Conformity is required. Buyers reject SEP valves regularly because "there is no CE mark" - but for a SEP valve, the missing CE mark is the legally correct condition, and a CE mark affixed to such a valve is actually a compliance defect, not a bonus. The practical habit worth building: in the material requisition, state the fluid, PS, TS and DN and let the classification decide the marking expectations, rather than blanket-demanding CE on every line item. Blanket CE demands push suppliers toward over-declared documents, which creates the mirror problem examined in Section 12.
Once a valve is Category I or above, the manufacturer selects a conformity assessment procedure from PED Article 14, and the module table defines who checks what:
Category | Available modules | Notified Body involvement | CE marking |
|---|---|---|---|
I | A (internal production control) | None | CE, no NB number |
II | A2, D1, E1 | Supervised final assessments or QA surveillance at random intervals | CE + NB number |
III | B (design type) + D, B (design type) + F, B (production type) + E, B (production type) + C2, H | Type examination plus production QA or product verification, or full QA | CE + NB number |
IV | B (production type) + D, B (production type) + F, G, H1 | As Category III with stricter production control | CE + NB number |
The module letters mean the following. Module A is the manufacturer's internal production control - self-assessment against the essential safety requirements. A2 adds supervised pressure testing at random intervals by a Notified Body; D1 and E1 add Notified Body approval of the production or final-inspection quality assurance system. Module B is an EU-type examination: the Notified Body examines a representative design against the essential safety requirements and issues a type certificate; it pairs with a production-side module - D (production quality assurance), F (product verification of each unit or batch), E (product quality assurance), or C2 (random final-product checks). Module G is unit verification, where the Notified Body examines each individual item - sensible for one-off large-bore valves. Modules H and H1 are full quality assurance covering design, production and final assessment, with H1 adding design examination by the Notified Body; a manufacturer may always apply a procedure belonging to a higher category, which is exactly what series valve producers do: they hold a Module H certificate, or B + D combinations, covering a whole valve range across categories. For a buyer, the module is not an abstraction: it tells you what surveillance the valve you receive actually passed through. Under Module H, your individual valve's conformity rests on the manufacturer's audited system plus the NB's unexpected visits; under B + F, a Notified Body verified the product side unit by unit or batch by batch. When a project specification asks for "PED 2014/68/EU, Category III minimum, Module B + D or H," it is selecting a surveillance philosophy, not adding words.
Most of the real work in a dual-certified valve happens in the places where PED's essential safety requirements go beyond what the ASME standards require or verify. Five of them account for most procurement failures.
PED Annex I point 4.3 gives only three legitimate routes for materials of main pressure-bearing parts in Categories II to IV: harmonised European standards (EN 10213 for castings, EN 10222 for forgings, the EN 10028 plate family and the like), European Approvals for Materials, or a Particular Material Appraisal - a documented assessment of an off-list material accepted by the Notified Body, which for Categories III and IV must be approved by the NB itself. A manufacturer buying ASTM A216 WCB or A105 therefore cannot simply drop those materials into a Category III PED valve on the strength of an ASME material certificate. Either the material has a dual EN listing with full certification to the harmonised standard, or a PMA dossier - chemistry, mechanicals, toughness, traceability - is written and NB-approved. This is the single most common technical gap when a predominantly ASME-oriented factory first takes PED orders, and it interacts directly with the certificate chain examined in our EN 10204 certificate guide: for main pressure-bearing parts in Categories II, III and IV, the material documentation must be a type 3.1 certificate of specific product control. One further clause catches importers of every nationality: where the material route relies on the manufacturer's own quality system, the relevant ISO 9001 certification must be issued by a certification body established in the EU - a document issue, but a document that Asian supply chains must verify annually.
PED Annex I point 7.5 sets a presumption floor for steels: elongation after rupture of at least 14 percent, and impact energy of at least 27 J on an ISO V-notch specimen, at a temperature not above 20 deg C and not above the lowest scheduled operating temperature. ASTM A216 WCB - the most common valve body carbon steel in the ASME world - does not require impact testing by default. A PED Category III valve in WCB therefore needs Charpy testing added to the material order, with the results carried on the 3.1 certificate, or the design minimum temperature limited to where untested WCB remains defensible. B16.34 itself has a parallel requirement for service below -29 deg C, so the two regimes converge at low temperature, but in the -29 to +20 deg C band a plain WCB valve can be fully ASME-compliant and fail the PED toughness presumption. The fix is procurement-side, not workshop-side: order the impact tests with the castings, as a line item, with the test temperature stated.
Under ASME Section IX, the manufacturer qualifies its own welding procedures and its own welders; the paper is self-certified and audited when someone looks. PED Annex I point 3.1.2 is stricter for Categories II, III and IV: operating procedures for permanent joining and the personnel who execute them must be approved by a competent third party - a Notified Body or a recognised third-party organisation. For a valve manufacturer, that means weld procedure qualification records and welder qualifications for pressure-boundary welds must carry third-party approval, not just in-house signatures. Plants that already hold both Section IX quals and PED approvals manage this routinely; plants approaching PED for the first time routinely discover it late, during type examination, when the NB reviews the joining dossier.
PED requires a final assessment of every item of pressure equipment: final inspection, proof of the safety devices where relevant, and a pressure test of the pressure envelope. The Directive's hydrostatic-test arithmetic is examined in Section 8 below. Beyond the test, the manufacturer must assemble and retain a technical file demonstrating compliance with the essential safety requirements - design calculations, drawings, material evidence, joining records, test reports, the hazard analysis - and keep it available to market surveillance authorities for ten years after the last unit of the type is placed on the market. The signed EU Declaration of Conformity travels with the product and must identify the valve, the Directive, the conformity route and the Notified Body where one is involved. None of this has an ASME analogue for valves: a B16.34 valve carries a test report; a PED valve carries a legal file with a retention clock on it.
For Categories II and above, the CE mark on the nameplate is followed by the four-digit identification number of the Notified Body involved in the production-phase assessment. A bare CE mark on a Category III valve is either a Category error or an imitation - both are findings worth escalating. The Declaration of Conformity must be accurate, current and traceable to the valve; a photocopied DoC from an unrelated order does not close the compliance chain. Marking details for the nameplate itself are covered in Section 10.
Requirement | ASME-side practice | PED requirement (Cat II-IV) |
|---|---|---|
Materials of main pressure parts | ASTM specs per B16.34 material groups; mill certs or 3.1 as ordered | Harmonised EN standard, EAM, or NB-approved PMA; EN 10204 3.1 mandatory |
Material toughness | Impact testing required only below -29 deg C for common carbon steels | Presumption: 14 percent elongation, 27 J ISO V at <= 20 deg C down to lowest service temperature |
Weld procedures and welders | Self-qualified per ASME Section IX | Approved by Notified Body or recognised third party |
Pressure test | B16.34 shell test at 1.5 x CWP (ambient) | Final assessment proof test; 1.43 x PS arithmetic where applied (see Section 8) |
Third-party oversight | None by default; buyer inspection optional | Notified Body per module; CE + NB number on Category II and above |
Documentation | Test report, material certs | DoC, technical file retained 10 years, O&M instructions in the language of use |
Dual-certified valves get tested once and reported twice, but the two test pressures are calculated on different bases, and the numbers are close enough that nobody notices when they differ - until an inspector does. On the ASME side, B16.34 requires the shell hydrostatic test at 1.5 times the cold working pressure rating at ambient temperature. For a Class 150 WCB valve, CWP is 19.6 bar, so the shell test is 29.4 bar - the arithmetic worked through in the B16.34 guide. On the PED side, Annex I point 7.4 states the hydrostatic test pressure for pressure vessels as the greater of 1.25 times the maximum service loading (with a stress-ratio correction for temperature) or 1.43 times the maximum allowable pressure, and point 3.2.2 extends the proof-test requirement to pressure equipment generally, "where appropriate" - for valves, the harmonised product standard EN 12266-1 and the manufacturer's specification define the exact pressures, and many PED valve programs apply the 1.43 x PS figure directly. For our Class 150 example with PS 19.6 bar: 1.43 x PS gives 28.0 bar against B16.34's 29.4 bar - a two-digit-percent overlap that means a single test at the B16.34 pressure generally satisfies both books, provided the test report cites both bases. The interesting case is hot service. The 1.25-term includes a stress ratio between test-temperature and design-temperature allowables; the crossover sits at a ratio of about 1.144, above which the temperature-corrected term exceeds 1.43 x PS. A valve rated by derated pressure at 300 deg C can therefore need a test pressure above the bare 1.43 x PS figure - one more reason the test report must state PS, TS and the calculation, not just a number. Note also that the PED proof test is a shell-strength test; seat leakage acceptance remains the leakage class from the specification, judged per API 598 or EN 12266 as the order defines - our API 598 testing guide covers those acceptance numbers.
Item | B16.34 basis (ASME side) | PED basis |
|---|---|---|
Governing clause | B16.34 hydrostatic shell test | Annex I 3.2.2 / 7.4; EN 12266-1 for valves |
Formula | 1.5 x CWP at ambient | Greater of 1.25 x service loading x stress ratio, or 1.43 x PS |
Class 150 WCB example (PS 19.6 bar) | 29.4 bar | 28.0 bar bare 1.43 x PS; higher if the stress-ratio term governs in hot service |
Temperature basis of the rating used | Cold working pressure at 38 deg C | PS at stated TS; derating handled in the stress ratio |
Seat test | Per API 598 / B16.34 | Per EN 12266 or specification; not the 1.43 arithmetic |
The practical assembly of a dual-certified valve range follows a pattern worth recognising, because it tells a buyer where to look for weak links. The design is checked once against B16.34 and once against the essential safety requirements - for most B16.34-shaped valves the geometry passes both with margin, and the harmonised EN design rules (or the calculation route of Annex I point 7.1) close the PED design file. Materials are sourced dual-listed where possible: forgings and castings certified to both the ASTM specification and the harmonised EN standard, with the EN certificate carrying the PED data, or covered by an NB-approved PMA where no dual route exists. Welding carries both ASME Section IX quals and NB-approved procedures and personnel. The conformity assessment is typically one of two shapes: a Module H full-quality-assurance certificate covering the whole valve range, with the NB auditing the system and visiting unannounced; or type certificates (Module B) per product family paired with production QA (Module D) or product verification (Module F). The nameplate then carries both stories at once: the class, CWP rating and material identification the ASME side expects, plus CE with the NB number, PS and TS limits the PED side requires. The marginal cost of genuine dual certification, done as above, is modest; the expensive failure mode is retrofitting PED evidence onto a finished ASME order, where missing Charpy data, self-qualified welders and untraceable material heats each reopen manufacturing decisions that were already closed. Projects that know they need both should put both in the RFQ from day one - classification data included.
A dual-certified valve nameplate is a layered document, and each layer answers to a different authority. The valve marking tradition - size, class or PN rating, material designation, manufacturer's mark, flow direction for unidirectional valves - comes from the product standards on each side (B16.34 marking requirements on the ASME side; EN 19 fields on the European side, which also fixes the order of the markings). The PED layer adds specific entries: the CE mark, followed by the Notified Body number for Category II and above; the maximum allowable pressure PS and the maximum and minimum allowable temperatures TS, marked as operating limits rather than as a class; the year of manufacture; and manufacturer identification sufficient for the Declaration of Conformity to point at the unit. EN 19-based practice places PS max and TS max on the tag plate explicitly - a genuinely useful addition for operators, because a class number alone does not tell the field what the derated pressure is at temperature; that translation is the whole subject of the B16.34 rating tables. Serial numbers deserve a note of their own: the DoC, the 3.1 certificates and the test report should all reference the same serial or batch identity, because that chain - not the CE mark alone - is what an auditor reconstructs.
A dual-certified shipment should arrive with a documentation package that reads like two dossiers sharing one spine. The PED side: the signed EU Declaration of Conformity identifying the valve model and serial range, the Directive, the category and module, and the Notified Body where applicable; EN 10204 type 3.1 certificates for main pressure-bearing parts (Categories II to IV); the final assessment report including the shell proof test; operating and maintenance instructions in the language of the country of use - a legal PED requirement, not a courtesy; and the NB certificate reference. The ASME side: the material certificates per the ASTM specifications, the pressure-temperature rating derivation where the order asks for it, the API 598 or B16.34 test report, and any special-test records (fire-safe, cryogenic, low-leakage) that were ordered. The manufacturer additionally holds the technical file, retained for ten years, available to authorities on request; buyers cannot audit that file's existence at delivery, but they can contract for it - some project specifications require a statement that the technical file exists and will remain available, which is a sensible clause for high-consequence service. What the package should not contain is documentation borrowed from the wrong order: each certificate and each DoC must trace to the serial numbers shipped.
Failed dual-certification orders present recognisable signatures. The table below lists the ones that recur, with the underlying cause and the response that resolves it.
Signature | What it means | Response |
|---|---|---|
Bare CE mark on a large Group-1 gas valve, no NB number | Category error or fictitious conformity; Category III requires CE + NB number | Request the DoC and NB certificate; reject the shipment until the route is evidenced |
CE mark on a DN25 SEP valve | CE not permitted for SEP under Article 4(3) | Not an improvement; ask why the classification was over-declared |
DoC cites PED but no module or NB | Declaration assembled after the fact; category and route undefined | Require category, module and NB number in the RFQ text and in the DoC |
3.1 certificates to ASTM only, no EN/PED data | Material route not closed for Cat II-IV; PMA may be missing | Ask for the harmonised-standard certificate or the NB-approved PMA reference |
WCB valve, no Charpy on the certificates | PED 7.5 toughness presumption unverified | Impact tests added at the casting order; certificate updated before shipment |
Weld quals self-signed, no third-party approval | Annex I 3.1.2 gap for Cat II-IV | NB or recognised-third-party approval of WPS and welders before production |
O&M manual only in the manufacturer's language | PED requires instructions in the language of the country of use | Translation contracted at order time, not at shipment |
Test report pressure stated without basis | Nobody can confirm which arithmetic governed | Report must state CWP/PS, TS and the formula; see Section 8 |
The clauses below convert the two regimes into RFQ language. Written this way, they force the classification and the evidence chain to exist before the valve does.
Clause | What to specify |
|---|---|
Service data for classification | Fluid and fluid group, state, PS and TS at design conditions, DN - stated per line item, not per project |
Category and module | Required PED category stated for information; module B + D, B + F or H for Cat III; DoC to carry category, module and NB number |
Materials | Harmonised EN certification, or NB-approved PMA; EN 10204 3.1 for main pressure parts in Cat II-IV |
Toughness | Charpy V-notch at the lowest scheduled operating temperature, >= 27 J expectation, results on the 3.1 certificate - stated explicitly for WCB |
Welding | WPS/PQR and welders for pressure-boundary welds approved by NB or recognised third party for Cat II-IV |
Proof test | Shell test per B16.34 (1.5 x CWP) with the report also stating the PED basis (1.43 x PS where applied) and TS |
Marking | CE + NB number per category; PS/TS limits on the nameplate; EN 19 field set; serial number consistent across documents |
Documents with shipment | DoC, 3.1 certificates, final assessment report, test report, O&M instructions in the language of use, NB certificate reference |
Retention | Statement that the PED technical file exists and remains available per the 10-year requirement |
Other directives | ATEX for actuated valves in hazardous areas, EMC, and Machinery Directive interfaces identified separately - not bundled into "PED certified" |
Handled this way, dual certification stops being a phrase and becomes a verifiable engineering and legal state: the valve is designed and made to the ASME standards, classified and assessed under PED with the right module, marked and documented so both stories can be reconstructed by any auditor, inspector or notified body that ever asks. More valve selection, testing and compliance topics are collected in the technical article library, and the casting-side quality questions behind material routes - radiography levels, casting factors and repair-weld policy - are treated in our forged versus cast valve body guide.
What does PED certification actually mean for an industrial valve?
PED 2014/68/EU is European law, not an engineering standard: it decides whether a valve with a maximum allowable pressure above 0.5 bar may lawfully be placed on the EU market. A valve enters as a pressure accessory and is classified by fluid group, fluid state, DN and the product of PS times DN into SEP or Categories I to IV. From Category I upward the manufacturer must meet the essential safety requirements through a defined conformity assessment module, affix CE marking followed by the Notified Body number for Category II and above, sign an EU Declaration of Conformity, and hold a technical file for ten years. CE marking says nothing about performance level - it is a legal statement of regulatory compliance.
Can a valve be ASME and PED certified at the same time?
Yes, and that is exactly what a dual-certified valve is - the two regimes stack rather than substitute. The engineering side is built to ASME B16.34: pressure-temperature ratings, shell design, materials, Section IX welding and API 598 testing, none of which carries a third-party stamp for valves. The legal side is PED conformity: classification, the chosen module, Notified Body involvement for Category II and above, CE marking and the Declaration of Conformity. The same shell test generally covers both - 1.5 times CWP under B16.34 gives 29.4 bar for a Class 150 WCB valve, while 1.43 times PS gives 28.0 bar - provided the test report cites both bases. The real work sits in materials (harmonised EN certification or an approved PMA), toughness data and third-party-approved welding, which PED demands and the ASME standards leave to self-certification.
What PED category will my valve fall into?
It depends on four inputs the buyer must state: the fluid group (Group 1 for flammable, toxic or oxidising fluids, Group 2 for steam, air, water and the rest), the state of the fluid, and the pair PS and DN. For Group 1 gas service, a valve with DN up to 25 is outside the categories entirely (Sound Engineering Practice); DN 25 to 100 with PS times DN up to 1000 is Category I; beyond DN 100 the band runs to PS times DN 3500 for Category II, and anything above that - or DN above 350 - is Category III. A DN50 ball valve on natural gas at 16 bar is Category I; the same valve at 100 bar, giving PS times DN of 5000, is Category III. Never let an RFQ stop at 'Class 300' - without fluid, PS, TS and DN the supplier cannot classify the valve at all.
Why does my PED valve need Charpy testing when the ASME version didn't?
PED Annex I point 7.5 presumes a steel is sufficiently ductile if it shows at least 14 percent elongation after rupture and an impact energy of at least 27 J on an ISO V-notch specimen at a temperature not above 20 deg C and not above the lowest scheduled operating temperature. ASTM A216 WCB - the workhorse carbon steel valve body - does not require impact testing by default, so a plain WCB valve can be fully ASME-compliant yet fail the PED presumption in the -29 to +20 deg C band. B16.34 does require impact testing below -29 deg C, so the two regimes converge there. The fix is procurement-side: order the Charpy tests with the castings as a line item, state the test temperature, and require the results on the EN 10204 3.1 certificate.
Do valves below Category I need any PED paperwork at all?
They need some, but not CE. Valves below Category I are governed by Article 4(3), Sound Engineering Practice: the manufacturer must design and make them to the sound engineering practice of a member state, supply adequate instructions for use, and identify itself. No CE mark may be affixed for PED and no Declaration of Conformity is required - so for a SEP valve the missing CE mark is the legally correct condition. A CE mark on a small SEP valve is actually a compliance defect, not a bonus, and usually signals an over-declared classification elsewhere in the paperwork. State the fluid, PS, TS and DN in the requisition and let the classification decide the marking expectations instead of blanket-demanding CE on every line.